If the RAINPOINT 20026-2 does not operate as expected, the following checks cover the common conditions described in the user manual.
Condition 1: Water leaks between the watering wand and garden hose
Possible Cause
The threaded connection may be loose or incompletely sealed.
What to Do
- Turn off the water supply.
- Disconnect the garden hose.
- Check the existing rubber washer.
- Add an additional rubber washer if necessary.
- Reconnect the hose.
- Tighten the connection securely.
- Turn the water back on and check again.
The manual allows two rubber washers to be used together when additional sealing is required.
Condition 2: Water leaks around the spray head
Possible Causes
- The Phillips screw may be loose.
- The spray head may not be fully rotated into its locked spray position.
What to Do
Check the Phillips Screw
Tighten the screw using a Phillips screwdriver.
Check the Spray Head
Rotate the spray head until it reaches the selected position and you hear a: “click”
This indicates that the spray head has reached the locked position.
Frequently Asked Questions
How many spray patterns does the 20026-2 have?
The 20026-2 provides 9 spray patterns:
ANGLE, FLAT, FLOOD, MIST, JET, CENTRE, FAN, CONE, and SHOWER.
How do I change the spray pattern?
Rotate the spray head until the desired spray pattern is selected.
Make sure it reaches the correct position before use.
How do I turn the water on or off from the wand?
Use the ON/OFF switch on the handle.
Does the switch adjust the water flow continuously?
The current manual only identifies the control as: ON / OFF
It does not specify continuous flow adjustment.
What size garden hose connection does the watering wand use?
The water inlet uses a: 3/4" thread
What is the maximum working pressure?
80 PSI (5.5 bar)
Do not operate the watering wand above this pressure.
What is the 20026-2 made of?
The manual specifies:
- Aluminum-alloy wand
- TPR handle
- ABS nozzle
- PP switch
Does the watering wand include a rubber washer?
Yes.
A built-in rubber washer is shown at the garden-hose connection.
What should I do if the hose connection leaks?
Check the rubber washer.
If necessary, add a second rubber washer before reconnecting the garden hose.
Why does water leak around the spray head?
Check whether:
- The Phillips screw is loose, or
- The spray head has not fully reached its locked position.
Can the 20026-2 be used with hot water?
No.
The manual advises against hot-water applications.
Can I use pesticides or chemicals with the watering wand?
No.
The product is intended for clean water only.
Do not use:
- Pesticides
- Car-wash foaming agents
- Other chemical products
These products may cause corrosion or damage.
Can I drink water from a garden hose connected to the watering wand?
No.
The manual warns that water from a garden hose may become contaminated and should not be consumed.
Is the 20026-2 suitable for commercial or high-pressure use?
No.
The manual specifies general outdoor use at:
80 PSI or less
and advises against commercial or high-pressure applications.
Care & Storage
Turn Off the Water After Use
Do not leave the watering wand unattended while the water is running.
Turn off the water supply after use.
Freezing or Extremely Hot Weather
During freezing or extremely hot weather:
- Disconnect the hose and watering wand from the water source.
- Drain remaining water.
- Store the product indoors.
This helps reduce temperature-related product damage.
Safety
Use Clean Water Only
Do not use pesticides, foaming agents, or other chemical products.
Keep Away from Children
The product is not a toy.
Keep it out of reach of children.
Do Not Direct High-Pressure Water at People, Pets, or Fragile Objects
High-pressure spray may cause personal injury or property damage.
Do Not Exceed the Pressure Limit
Maximum working pressure: 80 PSI / 5.5 bar
Comments
Please sign in to leave a comment.