If the JS-DIS101 does not water as expected, the following checks cover the most common installation and operating conditions.
Condition 1: No water comes from one shower head
Possible Cause
The nozzle may be damaged.
What to Do
Replace the affected shower head with a new one.
Condition 2: Spray is uneven between shower heads
Possible Cause
The nozzles may be set at different rotation angles.
What to Do
Rotate the shower heads to adjust the spray pattern and water volume.
Adjust each nozzle individually until the desired distribution is achieved.
Condition 3: Water leaks from a three-way socket
Possible Cause
The tubing or shower head is not fully or correctly inserted into the socket.
What to Do
- Turn off the water.
- Disconnect the affected component.
- Reinsert it securely into the three-way socket.
- Make sure it reaches the bottom of the connector.
- Turn the water back on and check again.
Condition 4: Water leaks between the quick connector and faucet
Possible Cause
The faucet connection is not sealing correctly.
What to Do
- Turn off the water.
- Disconnect the quick connector.
- Wrap PTFE thread-seal tape around the faucet thread if needed.
- Install a rubber washer at the product's water inlet.
- Reconnect the quick connector securely.
The quick connector already contains a built-in filter. If leakage remains, an additional rubber washer may be used to improve the seal.
Condition 5: Water leaks from the end plug
Possible Cause
The end plug is not properly connected to the final three-way socket.
What to Do
- Remove and reinstall the end plug correctly, or
- Replace the end plug if damaged.
Condition 6: Water flow becomes weak
What to Check
- Make sure the tubing is not kinked.
- Check that all connections are fully inserted.
- Check the filter screen for debris.
- Confirm that the water pressure is within 40–60 PSI.
Frequently Asked Questions
What water pressure should I use?
The recommended pressure range is: 40–60 PSI
Can I change the spray pattern?
Yes.
Rotate the nozzle head to switch between:
- Water Column Mode
- Spray Mode
Can each shower head be adjusted separately?
Yes.
Each shower head can be rotated independently to adjust its spray pattern and water volume.
Do I need tools or hot water to connect the tubing?
No.
The three-way sockets use a push-fit connection.
Simply push the tubing fully into the connector.
How do I remove tubing from a three-way socket?
Press the inner release ring and pull the tubing out.
Why is a single nozzle not spraying?
The troubleshooting section identifies a damaged nozzle as a possible cause.
Replace the affected nozzle if necessary.
Is there a filter in the system?
Yes.
The quick connector includes a pre-installed filter screen.
Should I clean the filter?
Yes.
Clean the filter screen regularly to help prevent clogging and maintain smooth water flow.
Maintenance & Cleaning
Clean the Filter Screen
Regularly inspect and clean the filter screen.
Debris in the filter may reduce water flow through the system.
Keep the Tubing Free from Kinks
Do not fold or sharply bend the tubing.
Kinks may restrict water flow to downstream shower heads.
Winter Freeze Protection
Before freezing weather:
- Turn off the main water supply.
- Drain all water from the irrigation system.
- Store the system where appropriate to prevent freeze damage.
Long-Term Storage
If the JS-DIS101 will not be used for an extended period:
- Disconnect the water supply.
- Drain all water from the tubing.
- Clean the filter.
- Store the system in a dry, frost-free environment.
Safety
The manual provides the following safety guidance:
- Do not drink water from this irrigation system.
- Keep the product out of reach of children.
- Do not use it for commercial, hot-water, or high-pressure applications.
- Do not leave the system unattended while operating.
- Disconnect and store the system indoors during freezing conditions or extreme heat.
- Do not direct the spray toward people, pets, or fragile objects.
Warranty
The JS-DIS101 manual states that the product has a 5-year limited warranty for the original purchaser/user against defects in materials or workmanship, subject to the conditions and exclusions described in the manual.
Comments
Please sign in to leave a comment.